Trucks
Showing 1–99 of 495 results
-
Water drain/filter combination for Portal Lift 17 Vario
Water separator, fitted in factory | to protect the control system and pump from harmful condensation | max. operating pressure 16 bar
-
Accessories holder for Portal Lift
6 slots, attached to lifting unit
-
Adaption for flywheel cDISK
Positive fit by means of hexagon bolts, diameter: 450 mm, yellow chromated, weight: 1.5 kg, load bearing capacity: 80 kg, additional pitch circle diameter 410 mm + 375 mm
-
Adjustable drive
Additional adjustable drive to mobilise the fixed lifting unit, incl. extended hanging control pad, reversing device, chain and cover
-
Automatic ”run-into” protection
Light barrier max.15 m
-
Automatic ”run-into” protection
Position indicator for craneway
-
Automatic ”run-into” protection
Mount for automatic ”run-into” protection according to requirements
-
Automatic axle distance preselection
AAV-Control
-
C-clip cDISK
For the installation and removal of couplings and control disks in a restricted installation space,rn(E.g. Cross-linking, connection only with basic device cDISK 3745410) capacity 80 kg
-
Cable suspension
For electric or compressed air cables, especially suitable for installation in pits with overhang | sold by the meter, installation by the customer
-
Cable suspension
Balancer to disconnect hand-held control panel
-
Cable suspension
Mount for running rail according to requirements
-
Calibration fee (net) for all tyre gauges Pneutruck
-
Cassette extended (primary coated)
Incl. galvanized slide covering, per meter
-
Cassette extended (primary coated)
Incl. FLEXCOVER, per meter
-
Cassette galvanized
Instead of primary coat, per meter
-
Cross-beam for ArtisLift MRG55
15 t
-
Diagnostic kit STDADIAG
IDC5 KIT TEXA – for diagnostic wheel alignment | kit for those who have a wheel alignment but no TEXA accessories
-
Diagnostic kit STDADIAG/SW
TEXA IDC5 SW KIT – for diagnostic wheel alignment | kit for those who already have TEXA devices (e.g., ADAS RCSS)
-
Die cast housing cDISK
yellow-chromatised, weight: 6 kg, capacity: 80 kg
-
Drive-on ramp kit for ExaLift HDVL | 2510 mm | galvanized
2510 mm, hot galvanized version | ideal for low-floor vehicles, dowel to the floor (fixing material not included) | for ExaLift HDVL | 1 set / 2 pieces
-
Drive-on ramp kit for ExaLift HDVL | 3300 mm | galvanized
3300 mm, hot galvanized version | ideal for low-floor vehicles, dowel to the floor (fixing material not included) | for ExaLift HDVL | 1 set / 2 pieces
-
Drive-on ramp kit for ExaLift HDVL | 3300 mm | lacquered
3300 mm, lacquered version | ideal for low-floor vehicles, dowel to the floor (fixing material not included) | for ExaLift HDVL | 1 set / 2 pieces
-
EvoBus Extra kit for pressure plate cDISK
yellow-chromatised, capacity: 80 kg
-
Floor leveling for HDVL 25/35-100-I
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 10 m platform length
-
Floor leveling for HDVL 25/35-100-I | galvanized
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 10 m platSafety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, form length | hot galvanized version
-
Floor leveling for HDVL 25/35-130/145-I
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 13/14,5 m platform length
-
Floor leveling for HDVL 25/35-130/145-I | galvanized
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 13/14.5 m platSafety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, form length | hot galvanized version
-
Floor leveling for HDVL 25/35-80-I
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 8 m platSafety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, form length
-
Floor leveling for HDVL 25/35-80-I | galvanized
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 8 m platSafety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, form length | hot galvanized version
-
Floor leveling for HDVL 25/35-90-I
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 9 m platSafety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, form length
-
Floor leveling for HDVL 25/35-90-I | galvanized
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 9 m platSafety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, form length | hot galvanized version
-
Floor stand
800 mm wide (for T/L-4 platform)
-
Floor stand
1000 mm wide (for T/L-5 platform)
-
Frame extended (primary copated)
Incl. galvanised slide covering, per meter
-
Frame extended (primary copated)
Incl. FLEXCOVER, per meter
-
Frame galvanized
Instead of primary coat, per meter
-
Frame with overhang
incl. galvanised slide covering, each piece
-
Frame with overhang
galvanised execution, incl. galvanised slide covering, each piece
-
Frame with overhang
Frame incl. FLEXCOVER, each piece
-
Frame with overhang
Frame, galvanised execution, incl. FLEXCOVER, each piece
-
Front and rear adapters for HydroLift
16.4 t | for lifting various tractors, incl. various agricultural adapters
-
Jacking beam
13.5 t, hand pump
-
Kit MRG pour ArtisLift MRG-25-4
10 m power cable with CEE plug, incl. 1 litre spindle oil | 1 set – only valid for ArtisLift MRG-25 with 4 lifting units
-
LED lighting kit for Exa Lift HDVL | 8-way
8-way | for HDVL lifts with 11, 12, 13 or 14,5 m platform length | suitable for washing bay, mounted on the inside of the rails
-
LED lighting kit Standard | for HydroLift 6,2/7,5/8,2
Incl. cable set, bracket and installation instructions | 2 pieces
-
MRG-Kit for MRG-55
10 m power cable with CEE plug and 1 litre spindle oil | 1 set – only valid for ArtisLift MRG-55 with 4 lifting units, when expanding to a set of 6 or 8, 2 units must be ordered
-
Pad
Steel clamp | load capacity 17 t | 1 piece
-
Pad R
Support plate, rubber pad, round | load capacity 15 t, peg Ø 55 mm | 1 piece
-
Protection cover for HydroLift 6,2/7,5
Flexible, sturdy protective cover with magnets to prevent splashing water | Only for battery-powered wheel grippers | 1 piece
-
Protection cover for HydroLift 8,2
Flexible, sturdy protective cover with magnets to prevent splashing water | Only for battery-powered wheel grippers | 1 piece
-
Pump sump
for lift cassette
-
Retrofit kit Fast clamps
CCD kit for 3D Quick-clamps (VSG.FC167.701916 to VSG.FC169.701923) | 1 set / 2 pieces
-
Roll cover Flexcover
driveable with 5.0t wheel load, galvanized
-
Stand for the control cabine | 600 mm
1 piece
-
Support plate mount
1 included in the scope of delivery, 1 more recommended if the distance between the mounting points is less than 550 mm
-
Support trestle
10000 kg, 1235 – 2040 mm, height adjustable in 6 x 100 mm steps, additionally with infinitely adjustable upper part (115 mm), 2 rollers, U-shaped holder and prismatic holder (interchangeable) | Grey (RAL 7040)
-
Support trestle
10000 kg, 1235 – 2040 mm, height adjustable in 6 x 100 mm steps, additionally with infinitely adjustable upper part (115 mm), 3 springy wheels, U-shaped holder and prismatic holder (interchangeable), ready assembled | Grey (RAL 7040)
-
Support trestle
7500 kg, 1330 – 2030 mm, height adjustable in 7 x 100 mm steps, 2 castors, U-bracket | Grey (RAL 7040)
-
Surcharge for rail chassis with lateral flanged rollers (set consisting of 4 pieces)
-
Surcharge rollers with special profile
-
Synchronization control Twin | for Exa Lift HDVL
2 lifts synchronised or individually movable | incl. 2 separate control boxes with controls and cable with plug
-
Temporary cover
Wooden slats to insert in frame, capacity: max. 100 kg/m², per meter
-
Transport trolley SmartCart XS | for Duplex load-carrying equipment
The convenient workshop helper with 33 slots – the attachments find their place in a tidy manner
-
Traverse for HydroLift 6,2
Max. load bearing capacity 12.4 t, king pin support | only in conjunction with traverse (item no. 120204)
-
Traverse for HydroLift 6,2
12.4 t
-
Traverse for HydroLift S3 7,5/8,2
16.4 t
-
Traverse for HydroLift S3 7,5/8,2
Max. load bearing capacity 16.4 t, king pin support | only in conjunction with traverse (item no. 119777)
-
Trolley SmartCart
for DUPLEX load-carrying equipment, incl. 4 swiveling rollers
-
Universal support Ø 35 mm
Mounting hole Ø 35 mm, suitable for holding various tools, such as the transmission plate GA passenger car | fitted with a bushing
-
Wheel clamps Fast clamps
Quick-clamps | for 3D wheel aligners, passenger car, tyre size 21 – 31″, wheel Ø 540 – 780 mm, clamps weight 3.5 kg (per set) | 1 set / 2 pieces
-
Wheel clamps Fast clamps
Quick-clamps | for CCD wheel aligners, passenger car, tyre size 21 – 31″, wheel Ø 540 – 780 mm, clamps weight 3.8 kg (per set) | 1 set / 2 pieces
-
Wheel fork extension for ArtisLift MRG55
Length approx. 123 mm | load capacity is reduced to 5 t | 1 set (for 1 wheel gripper)
-
Wheel fork reduction for mobile column lifts | tires Ø 800 – 700 mm
Reduction of the wheel fork for tires from Ø 800 mm to Ø 700 mm | 1 piece/per column
-
Floor leveling for HDVL 25/35-110-I | galvanized
For vertical scissor lifts with 11 m platform length
-
Floor leveling for HDVL 25/35-120-I | galvanized
For vertical scissor lifts with 12 m platform length
-
Floor leveling for HDVL 25/35-60-I | galvanized
For vertical scissor lifts with 6 m platform length
-
LED lighting kit for Exa Lift HDVL | 6-way
8 / 9 / 10 m
-
Vertical scissor lift ExaLift HDVL 25-60-I-HG
25 t, platform length 6000 mm, electro-hydraulic, safety latch, inground, hot galvanized version, control unit lacquered
-
Vertical scissor lift ExaLift HDVL 25-60-I
25 t, platform length 6000 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 25-80-I-HG
25 t, platform length 8000 mm, electro-hydraulic, safety latch, inground, hot galvanized version, control unit lacquered
-
Vertical scissor lift ExaLift HDVL 25-80-I
25 t, platform length 8000 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 25-90-I-HG
25 t, platform length 9000 mm, electro-hydraulic, safety latch, inground, hot galvanized version, control unit lacquered
-
Vertical scissor lift ExaLift HDVL 25-90-I
25 t, platform length 9000 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 25-100-I-HG
25 t, platform length 10000 mm, electro-hydraulic, safety latch, inground, hot galvanized version
-
Vertical scissor lift ExaLift HDVL 25-100-I
25 t, platform length 10000 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 25-110-I-HG
25 t, platform length 11000 mm, electro-hydraulic, safety latch, inground, hot galvanized version, control unit lacquered
-
Vertical scissor lift ExaLift HDVL 25-110-I
25 t, platform length 11000 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 25-120-I-HG
25 t, platform length 12000 mm, electro-hydraulic, safety latch, inground, hot galvanized version, control unit lacquered
-
Vertical scissor lift ExaLift HDVL 25-120-I
25 t, platform length 12000 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 25-130-I-HG
25 t, platform length 13000 mm, electro-hydraulic, safety latch, inground, hot galvanized version, control unit lacquered
-
Vertical scissor lift ExaLift HDVL 25-130-I
25 t, platform length 13000 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 25-145-I-HG
25 t, platform length 14500 mm, electro-hydraulic, safety latch, inground, hot galvanized version, control unit lacquered
-
Vertical scissor lift ExaLift HDVL 25-145-I
25 t, platform length 14500 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 35-60-I
35 t, platform length 6000 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 35-60-I-HG
35 t, platform length 6000 mm, electro-hydraulic, safety latch, inground, hot galvanized version
-
Vertical scissor lift ExaLift HDVL 35-80-I
35 t, platform length 8000 mm, electro-hydraulic, safety latch, inground, lacquered version
-
Vertical scissor lift ExaLift HDVL 35-80-I-HG
35 t, platform length 8000 mm, electro-hydraulic, safety latch, inground, hot galvanized version
-
Vertical scissor lift ExaLift HDVL 35-90-I-HG
35 t, platform length 9000 mm, electro-hydraulic, safety latch, inground, hot galvanized version