Trailer
Showing 1–99 of 295 results
-
Bushing 55/35
Peg diameter = 55 mm, standard Peg Ø of the axle traverse = 35 mm
-
Bushing 55/45
Peg diameter = 55 mm, standard Peg Ø of the axle traverse = 45 mm, with collar
-
Bushing 80/35
Peg diameter = 80 mm, standard Peg Ø of the axle traverse = 35 mm
-
Bushing 80/45
Peg diameter = 80 mm, standard Peg Ø of the axle traverse = 45 mm
-
Calibration fee (net) for all tyre gauges Pneutruck
-
Pit expansion BusStop
Abstract segment
-
Pit frame Type A
weight: 46 kg/m, a = 870 mm, per meter
-
Pit frame Type A
weight: 46 kg/m, a = 870 mm, per meter
-
Pit frame Type B
weight: 55Kg/m, a = 940 mm, per meter
-
Pit frame Type B
weight: 55 kg/m, a = 940 mm, per meter
-
Pit frame Type B1
weight: 42 kg/m, a = 940 mm, per meter
-
Pit frame Type B1
weight: 42 kg/m, a = 940 mm, per meter
-
Pit frame Type E
weight: 82 kg/m, a = 940 mm, per meter
-
Pit frame Type E
weight: 82 kg/m, a = 940 mm, per meter
-
Pit frame Type E1
weight: 69 kg/m, a = 940 mm, per meter
-
Pit frame Type E1
weight: 69 kg/m, a = 940 mm, per meter
-
Pit frame Type F
weight: 71.4 kg/m, a = 940 mm, per meter
-
Pit frame Type F
weight: 71.4 kg/m, a = 940 mm, per meter
-
Pit frame Type F1
weight: 62.5 kg/m, a = 940 mm, per meter
-
Pit frame Type F1
weight: 62.5 kg/m, a = 940 mm, per meter
-
Retrofit kit Fast clamps
CCD kit for 3D Quick-clamps (VSG.FC167.701916 to VSG.FC169.701923) | 1 set / 2 pieces
-
Segment Pit Covering
for monolithic constructed pits, per meter
-
Spacer DR 4
Height 400 mm, capacity 10 trnSpacer tubes to compensate for particularly large height differences between support bridges and load, with fall-through protection as standard, per piece
-
Spacer DR 4
-
Spacer DR 6
Height 600 mm, capacity 10 t
-
Surcharge for rail chassis with lateral flanged rollers (set consisting of 4 pieces)
-
Water drain/filter combination for Portal Lift 17 Vario
Water separator, fitted in factory | to protect the control system and pump from harmful condensation | max. operating pressure 16 bar
-
Universal support Ø 35 mm
Mounting hole Ø 35 mm, suitable for holding various tools, such as the transmission plate GA passenger car | fitted with a bushing
-
Front and rear adapters for HydroLift
16.4 t | for lifting various tractors, incl. various agricultural adapters
-
LED lighting kit Standard | for HydroLift 6,2/7,5/8,2
Incl. cable set, bracket and installation instructions | 2 pieces
-
Gearbox-plates GA III
Adjustment angle: ± 40° / ±17°, tensioning belt to secure the load, measurements adjustable to 600 x 400 mm, capacity 1 t, peg Ø 35 mm, measurements 400×300 mm
-
Gearbox-plates GA IV
Adjustment angle= ± 12°, weight = 23 kg, large rubber supporting surface, tensioning belts to secure the load, comfortable tilting in all directions by fork spanner, extremely flat construction, in series galvanised, capacity 1 t, peg Ø 35 mm, measurements 530x380x120 mm
-
Prismatic blocks
For GA IV | 2 pieces
-
Supporting bridge GSV
Adjustable 900 – 1180 mm, capacity 15 t, with Rollerset
-
Traverse for HydroLift S3 7,5/8,2
16.4 t
-
Supporting bridge SPZ-15
-
Traverse for HydroLift S3 7,5/8,2
Max. load bearing capacity 16.4 t, king pin support | only in conjunction with traverse (item no. 119777)
-
Water drain/filter combination
Water separator, fitted in factory | to protect the control system and pump from harmful condensation | max. operating pressure 16 bar
-
Traverse for HydroLift 6,2
Max. load bearing capacity 12.4 t, king pin support | only in conjunction with traverse (item no. 120204)
-
Traverse for HydroLift 6,2
12.4 t
-
Protection cover for HydroLift 6,2/7,5
Flexible, sturdy protective cover with magnets to prevent splashing water | Only for battery-powered wheel grippers | 1 piece
-
Support plate X
20 t, 55 mm peg diameter
-
Traverse ATEB S2
7.5 – 15 t, 55 mm peg diameter
-
Protection cover for HydroLift 8,2
Flexible, sturdy protective cover with magnets to prevent splashing water | Only for battery-powered wheel grippers | 1 piece
-
Cross-beam for ArtisLift MRG55
15 t
-
Trolley SmartCart
for DUPLEX load-carrying equipment, incl. 4 swiveling rollers
-
Wheel fork extension for ArtisLift MRG55
Length approx. 123 mm | load capacity is reduced to 5 t | 1 set (for 1 wheel gripper)
-
Wheel fork reduction for mobile column lifts | tires Ø 800 – 700 mm
Reduction of the wheel fork for tires from Ø 800 mm to Ø 700 mm | 1 piece/per column
-
Pads
Support plate, rubber support, round | R, 15 t, Ø 55 mm
-
Spacer DS 1
Height 100 mm, capacity 15 t
-
Spacer DS 2
Height 200 mm, capacity 15 t
-
Spacer DS 3
15 t, 35 mm peg diameter
-
Stand for the control cabine | 600 mm
1 piece
-
Support plate H
15 t, 35 mm peg diameter
-
Support plate P
15 t, 35 mm peg diameter
-
Support plate P MAN
15 t, 35 mm peg diameter
-
Support plate R
15 t, 35 mm peg diameter
-
Support plate U
15 t, 55 mm peg diameter
-
Support plate U
15 t, 35 mm peg diameter
-
Support plate U 145
15 t, 35 mm peg diameter
-
Support plate U 175
15 t, 35 mm peg diameter
-
Support plate U 220
15 t, 35 mm peg diameter
-
Support plate X
15 t, 35 mm peg diameter
-
Supporting bridge DB
Wooden blocks 100 x 200 x 360 mm, capacity 15 t
-
Transport trolley SmartCart XS | for Duplex load-carrying equipment
The convenient workshop helper with 33 slots – the attachments find their place in a tidy manner
-
Traverse ATB
15 t, 55 mm peg diameter, standard traverse for buses
-
Traverse ATS
15 t, 55 mm peg diameter
-
MRG-Kit for MRG-55
10 m power cable with CEE plug and 1 litre spindle oil | 1 set – only valid for ArtisLift MRG-55 with 4 lifting units, when expanding to a set of 6 or 8, 2 units must be ordered
-
Floor stand
800 mm wide (for T/L-4 platform)
-
Floor stand
1000 mm wide (for T/L-5 platform)
-
Traverse ATEB S2
7.5 – 15 t, 45 mm peg diameter
-
Kit MRG pour ArtisLift MRG-25-4
10 m power cable with CEE plug, incl. 1 litre spindle oil | 1 set – only valid for ArtisLift MRG-25 with 4 lifting units
-
Traverse ATS
20 t, 55 mm peg diameter
-
Spacer DR 5
Height 500 mm, capacity 15-30 t
-
Spacer DR 6
Height 600 mm, capacity 30 t
-
Support platform 15 t, mobile
Transportable support platform lowered under load, for use in conjunction with U-brackets, primed and lacquered
-
Supporting bridge GS
Universal, capacity 15 t, with Rollerset
-
Supporting bridge GSB
Extra flat, capacity 15 t, with Rollerset
-
Supporting bridge GSB Vario
Extra flat, capacity 15 t, with Rollerset
-
Supporting Package I
15 t, 55 mm peg diameter, navigable
-
Supporting Package II
15.5 t, 55 mm peg diameter, navigable
-
Supporting Package IV
15 t, 55 mm peg diameter, navigable
-
Traverse ATB MAN TGA-Set
15 t, 55 mm peg diameter
-
Traverse ATB Truck-Set
15 t, 55 mm peg diameter
-
Traverse ATK
15 t, 55 mm peg diameter
-
Diagnostic kit STDADIAG
IDC5 KIT TEXA – for diagnostic wheel alignment | kit for those who have a wheel alignment but no TEXA accessories
-
Diagnostic kit STDADIAG/SW
TEXA IDC5 SW KIT – for diagnostic wheel alignment | kit for those who already have TEXA devices (e.g., ADAS RCSS)
-
Supporting Package III
15 t, 55 mm peg diameter, navigable
-
Spacer DS 1
Height 100 mm, capacity 30 t
-
Spacer DS 2
30 t, 80 mm peg diameter
-
Spacer DS 3
Height 250 mm, capacity 30 t
-
Supporting bridge VS
Connecting set, capacity 30 t
-
Wheel clamps Fast clamps
Quick-clamps | for CCD wheel aligners, passenger car, tyre size 21 – 31″, wheel Ø 540 – 780 mm, clamps weight 3.8 kg (per set) | 1 set / 2 pieces
-
Spacer DS 2
Height 150 mm, capacity 30 t
-
Spacer DS 3
30 t, 55 mm peg diameter
-
Support plate H
20 t, 80 mm peg diameter
-
Support plate H
20 t, 55 mm peg diameter
-
Supporting bridge GS
Universal, capacity 20 t, with Rollerset
-
Supporting Package I
20 t, 55 mm peg diameter, navigable