Motor homes
Showing 298–396 of 587 results
-
Tyre changer HP641SQ.22FI
Mounting head and mounting lever, automatic, square standard chucking table, incl. tubeless tyre inflation device and plastic protection for ALU rims, passenger car, rim diameter 10 – 24.5″, max. rim width 12″ | Red (RAL 3002) | for all tyre types with max. wheel diameter 41″ (1050 mm)
-
Tyre changer HP641SQ.22
Mounting head and mounting lever, automatic, square standard chucking table, incl. plastic protection for ALU rims, passenger car, rim diameter 10 – 24.5″, max. rim width 12″ | Red (RAL 3002) | for all tyre types with max. wheel diameter 41″ (1050 mm)
-
Lifting table MGE 2.0
2.0 t, 1000 mm stroke, air hydraulic pump | Grey (RAL 7015)
-
Axial traverse ATB NF
10 t, peg Ø 55 mm, adjustment range 420 – 1020 mm | suitable for low-level buses | incl. 2 sliders and 2 adjustable receptacle pins
-
Axial traverse ATEB
10 t, peg Ø 55 mm
-
Axial traverse ATEB S2
7.5 – 15 t, peg Ø 45 mm
-
Axial traverse ATEB S2
7.5/15 t, peg Ø 45/55 mm, adjustment range 200 – 620/830 – 1500 mm | special cross bar for secure seating of EvoBus buses, in particular the CITARO series | incl. 4 pads and 2 sliders
-
Axial traverse ATH
1.5 t, peg Ø 35 mm, adjustment range 550 – 1200 mm, 1-fold telescopic | incl. 2 pads and 2 spacers
-
Axial traverse ATT 3,2
3.2 t, peg Ø 35 mm, adjustment range 630 – 1230 mm, 2-fold telescopic, incl. carrying plates | safe 2-point-support of vehicles such as Mercedes-Benz Sprinter, VW – LT 2
-
Axial traverse ATT 3.2 C
3.2 t, peg Ø 55 mm, adjustment range 868 – 1660 mm, 2-fold telescopic | for passenger cars and vans | incl. pad
-
Bus traverse BEFV-15
Wide, extended version with extendable sliding pieces, extra flat, adjustment range 870 – 1200 mm (510 – 840 mm), load capacity 15 t (center) | 1 piece
-
Bushing 55/35
Peg Ø 55 mm, standard peg Ø gearbox plates 35 mm | for BLITZlifts with mount Ø 55 mm | 1 piece
-
Bushing 55/45
Peg Ø 55 mm, standard peg Ø gearbox plates 45 mm | for BLITZlifts with mount Ø 55 mm | 1 piece
-
Bushing 80/35
Peg Ø 80 mm, standard peg Ø gearbox plates 35 mm | for BLITZlifts with mount Ø 80 mm | 1 piece
-
Bushing 80/45
Peg Ø 80 mm, standard peg Ø gearbox plates 45 mm | for BLITZlifts with mount Ø 80 mm | 1 piece
-
Connecting pieces ZS 100
1.5 t, 100 mm | 1 set / 2 pieces
-
Connecting pieces ZS 50
1.5 t, 50 mm | 1 set / 2 pieces
-
Fastening set ATS
30 t, peg Ø 55 mm | for positioning a traverse safely on the supporting bridge GS
-
Fastening set ATS
10 t, peg Ø 35 mm | for positioning a traverse safely on the supporting bridge GS
-
Fastening set ATT 3,2
10 t, peg Ø 35 mm | for secure placement of an axial traverse ATT 3,2 on the supporting bridge GS / GSB
-
Gearbox plate GA III
Adjustment angle +/- 40° / +/- 17°, load capacity 1 t, peg Ø 35 mm, measurements 400 x 300 mm (adjustable up to 600 x 400 mm), tensioning belt to secure the load
-
Gearbox plate GA IV
Adjustment angle +/- 12°, load capacity 1 t, peg Ø 35 mm, measurements 546 x 381 mm, in series galvanised, tensioning belts to secure the load, large rubber supporting surface
-
Lowered traverse
Can travel along the whole adjusting range at floor level
-
Lowered traverse
In defined position, fitted at floor level
-
Mounting set for traverse ATT 3,2 C
Optional accessories for the transporter receptacle, recommended plug-in pick-up set | for cars / vans / MAN / Crafter / Sprinter
-
Pad A 120
Support plate, pin | load capacity 15 t, peg Ø 75 mm, Ø 120 mm | with handles | 1 piece
-
Pad A 50
Support plate, pin | load capacity 15 t, peg Ø 75 mm, Ø 50 mm | 1 piece
-
Pad A 60
Support plate, pin | load capacity 15 t, peg Ø 75 mm, Ø 60 mm | 1 piece
-
Pad E 140/100
Support plate, aluminum pad, rectangular | load capacity 15 t, peg Ø 75 mm | 1 piece
-
Pad E 190/230
Support plate, aluminum pad, rectangular | load capacity 15 t, peg Ø 75 mm | for traverse TEF 107445 | 1 piece
-
Pad E 270/230
Support plate, aluminum pad, rectangular | load capacity 15 t, peg Ø 75 mm | for traverse TEFV 11132 | 1 piece
-
Pad G 145/150
Supporting fork | load capacity 15 t, peg Ø 75 mm | for rear axles with differential | 1 piece
-
Pad G 185/150
Supporting fork | load capacity 15 t, peg Ø 75 mm | for rear axles with differential | 1 piece
-
Pad G 220/110
Supporting fork | load capacity 15 t, peg Ø 75 mm | for rear axles with differential | 1 piece
-
Pad G 260/190
Supporting fork | load capacity 15 t, peg Ø 75 mm | for rear axles with differential | 1 piece
-
Pad G 30/80
Supporting fork | load capacity 15 t, peg Ø 75 mm | 1 piece
-
Pad G 40/150
Supporting fork, standard | load capacity 15 t, peg Ø 75 mm | 1 piece
-
Pad G 40/90
Supporting fork | load capacity 15 t, peg Ø 75 mm | for supporting low-floor buses (MAN and DB CITARO) at the front axle | 1 piece
-
Pad G 50/60
Supporting fork | load capacity 15 t, peg Ø 75 mm | 1 piece
-
Pad H
Wooden clamp | load capacity 15 t, peg Ø 35 mm | 1 piece
-
Pad H
Wooden clamp | load capacity 20 t, peg Ø 80 mm | 1 piece
-
Pad H
Wooden clamp | load capacity 20 t, peg Ø 55 mm | 1 piece
-
Pad P
Support plate, pin | load capacity 15 t, peg Ø 35 mm | special support for buses on frame (mushroom shaped support) | 1 piece
-
Pad P MAN
Support plate, pin | load capacity 15 t, peg Ø 35 mm | special support for MAN trucks at the rear axle (mushroom shaped support) | 1 piece
-
Pad R
Support plate, rubber pad, round | load capacity 15 t, peg Ø 35 mm | 1 piece
-
Pad R 116
Support plate, rubber pad, round | load capacity 15 t, peg Ø 75 mm, Ø 116 mm | 1 piece
-
Pad R 150
Support plate, rubber pad, round | load capacity 15 t, peg Ø 75 mm, Ø 150 mm | 1 piece
-
Pad U
Support plate, fork | load capacity 15 t, peg Ø 55 mm | 1 piece
-
Pad U
Support plate, fork | load capacity 15 t, peg Ø 35 mm | 1 piece
-
Pad U 145
Support plate, fork | load capacity 15 t, peg Ø 35 mm | 1 piece
-
Pad U 175
Support plate, fork | load capacity 15 t, peg Ø 35 mm | 1 piece
-
Pad U 220
Support plate, fork | load capacity 15 t, peg Ø 35 mm | 1 piece
-
Pad X
Steel clamp | load capacity 30 t, peg Ø 80 mm | 1 piece
-
Pad X
Steel clamp | load capacity 20 t, peg Ø 55 mm | 1 piece
-
Pad X
Steel clamp | load capacity 15 t, peg Ø 35 mm | 1 piece
-
Pads
Support plate, rubber pad, rectangular | for Tesla | 1 set / 4 pieces
-
Pads
Prism | for Mercedes G-Class – front and rear | 1 set / 4 pieces
-
Pads
Mandrel | for Fiat Ducato, Peugeot Boxer, Citroën Jumper – front and rear | 1 set / 4 pieces
-
Pads
Prism, mandrel | for Mercedes Sprinter, VW Crafter | 1 set / 6 pieces
-
Pads
Support plate, U-support | 1 set / 4 pieces
-
Pads
Prism | for VW MEB platform E-vehicles | 1 set / 4 piece
-
Pads
Support plate, centering mushroom | for Fiat 500E, 500 ABARTH | 2-stage | 1 set / 4 pieces
-
Pit expansion BusStop
Abstract segment
-
Pit frame Type A
weight: 46 kg/m, a = 870 mm, per meter
-
Pit frame Type A
weight: 46 kg/m, a = 870 mm, per meter
-
Pit frame Type B
weight: 55Kg/m, a = 940 mm, per meter
-
Pit frame Type B
weight: 55 kg/m, a = 940 mm, per meter
-
Pit frame Type B1
weight: 42 kg/m, a = 940 mm, per meter
-
Pit frame Type B1
weight: 42 kg/m, a = 940 mm, per meter
-
Pit frame Type E
weight: 82 kg/m, a = 940 mm, per meter
-
Pit frame Type E
weight: 82 kg/m, a = 940 mm, per meter
-
Pit frame Type E1
weight: 69 kg/m, a = 940 mm, per meter
-
Pit frame Type E1
weight: 69 kg/m, a = 940 mm, per meter
-
Pit frame Type F
weight: 71.4 kg/m, a = 940 mm, per meter
-
Pit frame Type F
weight: 71.4 kg/m, a = 940 mm, per meter
-
Pit frame Type F1
weight: 62.5 kg/m, a = 940 mm, per meter, galvanised (both side)
-
Pit frame Type F1
weight: 62.5 kg/m, a = 940 mm, per meter, primecoated (both side)
-
Prismatic blocks
For GA IV | 2 pieces
-
Segment Pit Covering
for monolithic constructed pits, per meter
-
Spacer D 100
15 t, peg Ø 75 mm, 100 mm | 1 piece
-
Spacer D 200
15 t, peg Ø 75 mm, 200 mm | 1 piece
-
Spacer D 60
15 t, peg Ø 75 mm, 60 mm | 1 piece
-
Spacer DS 1
15 t, peg Ø 35 mm, 100 mm | 1 piece
-
Spacer DS 1
30 t, peg Ø 55 mm, 100 mm | 1 piece
-
Spacer DS 2
15 t, peg Ø 35 mm, 150 mm | 1 piece
-
Spacer DS 2
30 t, peg Ø 80 mm, 150 mm | 1 piece
-
Spacer DS 2
30 t, peg Ø 55 mm, 150 mm | 1 piece
-
Spacer DS 3
15 t, peg Ø 35 mm, 250 mm | 1 piece
-
Spacer DS 3
30 t, peg Ø 55 mm, 250 mm | 1 piece
-
Spacer DS 3
30 t, peg Ø 80 mm, 250 mm | 1 piece
-
Spacer tube DR 4
10 t, peg Ø 35 mm, 400 mm | 1 piece
-
Spacer tube DR 4
15 – 20 t, peg Ø 55 mm, 400 mm | 1 piece
-
Spacer tube DR 5
15 – 30 t, peg Ø 55 mm, 500 mm | 1 piece
-
Spacer tube DR 6
10 t, peg Ø 35 mm, 600 mm | 1 piece
-
Spacer tube DR 6
30 t, peg Ø 80 mm, 600 mm | 1 piece
-
Support platform
15 t, mobile | for use in conjunction with U-brackets, primed and lacquered, lowered under load
-
Supporting block DB
Wooden block, 100 x 200 x 360 mm, load capacity 15 t | for lowering the traverse onto the supporting bridge | 1 piece
-
Supporting bridge GS 10
10 t | Universal | to ensure that the vehicle is tilt-proof – pit lift can still be used | incl. roller set, 2 sliders, 2 spacer tubes, 2 pads, traverses and tool tray
-
Supporting bridge GS 15
15 t | Universal | to ensure that the vehicle is tilt-proof – pit lift can still be used | incl. roller set, 2 sliders, 2 spacer tubes, 2 pads, traverses and tool tray