Buses
Showing 1–99 of 463 results
-
Bushing 55/45
Peg diameter = 55 mm, standard Peg Ø of the axle traverse = 45 mm, with collar
-
Bushing 80/45
Peg diameter = 80 mm, standard Peg Ø of the axle traverse = 45 mm
-
Calibration fee (net) for all tyre gauges Pneutruck
-
Cassette extended (primary coated)
Incl. galvanized slide covering, per meter
-
Frame extended (primary copated)
Incl. galvanised slide covering, per meter
-
Frame with overhang
incl. galvanised slide covering, each piece
-
Frame with overhang
galvanised execution, incl. galvanised slide covering, each piece
-
Pit expansion BusStop
Abstract segment
-
Pit frame Type A
weight: 46 kg/m, a = 870 mm, per meter
-
Pit frame Type A
weight: 46 kg/m, a = 870 mm, per meter
-
Pit frame Type B
weight: 55Kg/m, a = 940 mm, per meter
-
Pit frame Type B
weight: 55 kg/m, a = 940 mm, per meter
-
Pit frame Type B1
weight: 42 kg/m, a = 940 mm, per meter
-
Pit frame Type B1
weight: 42 kg/m, a = 940 mm, per meter
-
Pit frame Type E
weight: 82 kg/m, a = 940 mm, per meter
-
Pit frame Type E
weight: 82 kg/m, a = 940 mm, per meter
-
Pit frame Type E1
weight: 69 kg/m, a = 940 mm, per meter
-
Pit frame Type E1
weight: 69 kg/m, a = 940 mm, per meter
-
Pit frame Type F
weight: 71.4 kg/m, a = 940 mm, per meter
-
Pit frame Type F
weight: 71.4 kg/m, a = 940 mm, per meter
-
Pit frame Type F1
weight: 62.5 kg/m, a = 940 mm, per meter
-
Pit frame Type F1
weight: 62.5 kg/m, a = 940 mm, per meter
-
Segment Pit Covering
for monolithic constructed pits, per meter
-
Spacer DR 4
Height 400 mm, capacity 10 trnSpacer tubes to compensate for particularly large height differences between support bridges and load, with fall-through protection as standard, per piece
-
Spacer DR 4
-
Spacer DR 6
Height 600 mm, capacity 10 t
-
Surcharge for rail chassis with lateral flanged rollers (set consisting of 4 pieces)
-
Water drain/filter combination for Portal Lift 17 Vario
Water separator, fitted in factory | to protect the control system and pump from harmful condensation | max. operating pressure 16 bar
-
Surcharge rollers with special profile
-
Pad R
Support plate, rubber pad, round | load capacity 15 t, peg Ø 55 mm | 1 piece
-
Gearbox plate GA III
Adjustment angle +/- 40° / +/- 17°, load capacity 1 t, peg Ø 35 mm, measurements 400 x 300 mm (adjustable up to 600 x 400 mm), tensioning belt to secure the load
-
Gearbox plate GA IV
Adjustment angle +/- 12°, load capacity 1 t, peg Ø 35 mm, measurements 546 x 381 mm, in series galvanised, tensioning belts to secure the load, large rubber supporting surface
-
Prismatic blocks
For GA IV | 2 pieces
-
Bushing 55/35
Peg Ø 55 mm, standard peg Ø gearbox plates 35 mm | for BLITZlifts with mount Ø 55 mm | 1 piece
-
Bushing 80/35
Peg Ø 80 mm, standard peg Ø gearbox plates 35 mm | for BLITZlifts with mount Ø 80 mm | 1 piece
-
Synchronization control Twin | for Exa Lift HDVL
2 lifts synchronised or individually movable | incl. 2 separate control boxes with controls and cable with plug
-
LED lighting kit for Exa Lift HDVL | 8-way
8-way | for HDVL lifts with 11, 12, 13 or 14,5 m platform length | suitable for washing bay, mounted on the inside of the rails
-
Support trestle
10000 kg, 1235 – 2040 mm, height adjustable in 6 x 100 mm steps, additionally with infinitely adjustable upper part (115 mm), 2 rollers, U-shaped holder and prismatic holder (interchangeable) | Grey (RAL 7040)
-
Support trestle
10000 kg, 1235 – 2040 mm, height adjustable in 6 x 100 mm steps, additionally with infinitely adjustable upper part (115 mm), 3 springy wheels, U-shaped holder and prismatic holder (interchangeable), ready assembled | Grey (RAL 7040)
-
Support trestle
7500 kg, 1330 – 2030 mm, height adjustable in 7 x 100 mm steps, 2 castors, U-bracket | Grey (RAL 7040)
-
Front and rear adapters for HydroLift
16.4 t | for lifting various tractors, incl. various agricultural adapters
-
LED lighting kit Standard | for HydroLift 6,2/7,5/8,2
Incl. cable set, bracket and installation instructions | 2 pieces
-
Cable suspension
For electric or compressed air cables, especially suitable for installation in pits with overhang | sold by the meter, installation by the customer
-
Diagnostic kit STDADIAG
IDC5 KIT TEXA – for diagnostic wheel alignment | kit for those who have a wheel alignment but no TEXA accessories
-
Diagnostic kit STDADIAG/SW
TEXA IDC5 SW KIT – for diagnostic wheel alignment | kit for those who already have TEXA devices (e.g., ADAS RCSS)
-
Drive-on ramp kit for ExaLift HDVL | 3300 mm | lacquered
3300 mm, lacquered version | ideal for low-floor vehicles, dowel to the floor (fixing material not included) | for ExaLift HDVL | 1 set / 2 pieces
-
Drive-on ramp kit for ExaLift HDVL | 2510 mm | galvanized
2510 mm, hot galvanized version | ideal for low-floor vehicles, dowel to the floor (fixing material not included) | for ExaLift HDVL | 1 set / 2 pieces
-
Drive-on ramp kit for ExaLift HDVL | 3300 mm | galvanized
3300 mm, hot galvanized version | ideal for low-floor vehicles, dowel to the floor (fixing material not included) | for ExaLift HDVL | 1 set / 2 pieces
-
Supporting bridge GSV
Adjustable 900 – 1180 mm, capacity 15 t, with Rollerset
-
Traverse for HydroLift S3 7,5/8,2
16.4 t
-
Supporting bridge SPZ-15
-
Traverse for HydroLift S3 7,5/8,2
Max. load bearing capacity 16.4 t, king pin support | only in conjunction with traverse (item no. 119777)
-
Water drain/filter combination
Water separator, fitted in factory | to protect the control system and pump from harmful condensation | max. operating pressure 16 bar
-
Wheel clamps Fast clamps
Quick-clamps | for CCD wheel aligners, passenger car, tyre size 21 – 31″, wheel Ø 540 – 780 mm, clamps weight 3.8 kg (per set) | 1 set / 2 pieces
-
Traverse for HydroLift 6,2
Max. load bearing capacity 12.4 t, king pin support | only in conjunction with traverse (item no. 120204)
-
Traverse for HydroLift 6,2
12.4 t
-
Wheel clamps Fast clamps
Quick-clamps | for 3D wheel aligners, passenger car, tyre size 21 – 31″, wheel Ø 540 – 780 mm, clamps weight 3.5 kg (per set) | 1 set / 2 pieces
-
Protection cover for HydroLift 6,2/7,5
Flexible, sturdy protective cover with magnets to prevent splashing water | Only for battery-powered wheel grippers | 1 piece
-
Support plate X
20 t, 55 mm peg diameter
-
Traverse ATEB S2
7.5 – 15 t, 55 mm peg diameter
-
Protection cover for HydroLift 8,2
Flexible, sturdy protective cover with magnets to prevent splashing water | Only for battery-powered wheel grippers | 1 piece
-
Jacking beam
13.5 t, hand pump
-
Floor leveling for HDVL 25/35-110-I | galvanized
For vertical scissor lifts with 11 m platform length
-
Floor leveling for HDVL 25/35-120-I | galvanized
For vertical scissor lifts with 12 m platform length
-
Floor leveling for HDVL 25/35-60-I | galvanized
For vertical scissor lifts with 6 m platform length
-
Adjustable drive
Additional adjustable drive to mobilise the fixed lifting unit, incl. extended hanging control pad, reversing device, chain and cover
-
Automatic ”run-into” protection
Light barrier max.15 m
-
Automatic ”run-into” protection
Position indicator for craneway
-
Automatic ”run-into” protection
Mount for automatic ”run-into” protection according to requirements
-
Automatic axle distance preselection
AAV-Control
-
Cable suspension
Balancer to disconnect hand-held control panel
-
Cable suspension
Mount for running rail according to requirements
-
Cross-beam for ArtisLift MRG55
15 t
-
Roll cover Flexcover
driveable with 5.0t wheel load, galvanized
-
Temporary cover
Wooden slats to insert in frame, capacity: max. 100 kg/m², per meter
-
Trolley SmartCart
for DUPLEX load-carrying equipment, incl. 4 swiveling rollers
-
Wheel fork extension for ArtisLift MRG55
Length approx. 123 mm | load capacity is reduced to 5 t | 1 set (for 1 wheel gripper)
-
Wheel fork reduction for mobile column lifts | tires Ø 800 – 700 mm
Reduction of the wheel fork for tires from Ø 800 mm to Ø 700 mm | 1 piece/per column
-
Universal support Ø 35 mm
Mounting hole Ø 35 mm, suitable for holding various tools, such as the transmission plate GA passenger car | fitted with a bushing
-
Floor leveling for HDVL 25/35-130/145-I
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 13/14,5 m platform length
-
Floor leveling for HDVL 25/35-130/145-I | galvanized
Safety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, for HDVL lifts with 13/14.5 m platSafety cover of the foundation opening when the lifting platform is raised, load capacity 500 kg, form length | hot galvanized version
-
Spacer DS 1
Height 100 mm, capacity 15 t
-
Spacer DS 2
Height 200 mm, capacity 15 t
-
Spacer DS 3
15 t, 35 mm peg diameter
-
Stand for the control cabine | 600 mm
1 piece
-
Support plate H
15 t, 35 mm peg diameter
-
Support plate P
15 t, 35 mm peg diameter
-
Support plate P MAN
15 t, 35 mm peg diameter
-
Support plate R
15 t, 35 mm peg diameter
-
Support plate U
15 t, 55 mm peg diameter
-
Support plate U
15 t, 35 mm peg diameter
-
Support plate U 145
15 t, 35 mm peg diameter
-
Support plate U 175
15 t, 35 mm peg diameter
-
Support plate U 220
15 t, 35 mm peg diameter
-
Support plate X
15 t, 35 mm peg diameter
-
Supporting bridge DB
Wooden blocks 100 x 200 x 360 mm, capacity 15 t
-
Transport trolley SmartCart XS | for Duplex load-carrying equipment
The convenient workshop helper with 33 slots – the attachments find their place in a tidy manner
-
Traverse ATB
15 t, 55 mm peg diameter, standard traverse for buses
-
Traverse ATS
15 t, 55 mm peg diameter