Accessories lifts
Accessories for workshop lifts can seriously make a difference. Our selection of accessories lifts includes kits, rubber pads, covers and much more.
Showing 199–297 of 624 results
Supporting arm extensions
Capacity reduced to 3.5 t | 1 set / 2 pieces
Supporting arm extensions
90 mm, capacity reduced to 2.7 t | 1 set / 2 pieces
Supporting arm extensions
90 mm, capacity reduced to 2.7 t | 1 set / 2 piec
Supporting arm extensions
100 mm, capacity reduced to 2.7 t | 1 set / 2 pieces
Supports for chassis lifting | adjustable | bushing Ø 45 mm | 1 set / 4 pieces
Needed spacers S224A3-A4, S370A18
Supports for chassis lifting | adjustable | bushing Ø 60 mm | 1 set / 4 pieces
Needed spacers S370A7-A8-A15
Supports for spacers, bushing Ø 45 mm
For 2-post lifts | 1 set / 2 pieces
Surcharge for rail chassis with lateral flanged rollers (set consisting of 4 pieces)
Tool trays | magnetic | 1 set / 4 pieces
Towing lever Capacity 3000 / 4000 / 5500 kg
Traverses for XS30-CAT
For vans and off-road vehicles | 1 set / 2 pieces
Turntable covers for 615 mm platforms
Spacers to completely close turntable recess | suitable for RAV.640N2.193117, RAV.640N2.193469, RAV.640N2.193001, RAV.640N2.193582, RAV.640N2.193216, RAV.640N3.192981 and RAV.640N2.193476 | 1 set / 2 pieces
U-support
Vehicles lift platforms 1 set / 4 pieces
Ramps for extra low clearance vehicles
Warning light
Light signal “system in use”
Warning light
Light signal “system in use”
Wheel alignment stands | load capacity per stand 800 kg
Accessory for wheel aligner | 1 set / 4 pieces
Wheel clamp mount
Adjustable special version, wheel Ø 500 – 1200 mm
Wheel fork extension 150 mm
Extensions for adjustable fork (1 per column) | 1 set
Wheel free cross beam for U-versions | capacity 15000 kg
Wheel free cross beam for U-versions | Capacity 20000 kg
Wheel free cross-beam max. 20000 kg
Crossbar for standard lifts with adjustable fork
Wheel-lifting platform kit
Width extendion 200 mm
200 mm
Width extendion 200 mm
Width extension
For 2-post lift KPX35LLE | enables columns to be widened up to 3200 mm
Rubber pads
160 x 120 x 80 mm | 1 set / 4 pieces
Rubber pads
160 x 120 x 40 mm | 1 set / 4 pieces
Drive-on ramps 2510 mm
Floor installation kit for lifts | 1 set / 2 pieces
Drive-on ramps 3300 mm
Floor installation kit for lifts | 1 set / 2 pieces
Retrofit kit Air supply
For jacking beam
Retrofit kit Parking position switch rolling jack
For scissor lift S38/S50
LED lighting kit 4-fold, 24 V, 4800 mm
Spacers for pads
4 x 89 mm, 4 x 127 mm, incl. 2 brackets for mounting on the pillars | for SPOA3T | 1 set / 8 pieces
Control unit installation kit
“m” meter, control unit left | mounting the operating unit in a special position – in drive-up direction “left” from the platform, at a distance of “m” meter | sold by the metre
Control unit installation kit
“m” meter, control unit right | mounting the operating unit in a special position – in drive-up direction “right” from the platform, at a distance of “m” meter | sold by the metre
Control unit installation kit
“m” meter, control unit left | mounting the operating unit in a special position – in drive-up direction “left” from the platform, at a distance of “m” meter | for lifts of the 800 series with floor compensation | sold by the metre
Control unit installation kit
“m” meter, control unit left | mounting the operating unit in a special position – in drive-up direction “left” from the platform, at a distance of “m” meter | for lifts of the 800 series with floor compensation | sold by the metre
Spacers for pads
4 x 200 mm, incl. bracket for mounting on the pillars | 1 set / 4 pieces
Support trestle
10000 kg, 1235 – 2040 mm | Grey (RAL 7040)
Support trestle
10000 kg, 1235 – 2040 mm | with on springs retracting rollers
Support trestle
7500 kg, 1330 – 2030 mm | Grey (RAL 7040)
Energy kit for S50/S42
Compressed air connection under the track, 230 V socket at the control panel | 1 piece
Hose cover 1 m, galvanised
Pads
Support plate, rubber pad, rectangular | for TESLA vehicles | 1 set / 4 pieces
Stands for alignment
1 set / 4 pieces
Vehicles lift platforms
Ramp height 60 mm, for extremely low vehicles | 1 set / 2 pieces
Control unit installation kit
2 m, control unit left | mounting the operating unit in a special position – in drive-up direction “left” from the platform, at a distance of 2 m
Control unit installation kit
2 m, control unit right | mounting the operating unit in a special position – in drive-up direction “right” from the platform, at a distance of 2 m
Tool support
Ergonomic holder for impact wrench
Traverse HydroLift S2
Capacity 16.4 t
Gearbox-plates GA III
Adjustment angle: ± 40° / ±17°, tensioning belt to secure the load, measurements adjustable to 600 x 400 mm, capacity 1 t, peg Ø 35 mm, measurements 400×300 mm
Gearbox-plates GA IV
Adjustment angle= ± 12°, weight = 23 kg, large rubber supporting surface, tensioning belts to secure the load, comfortable tilting in all directions by fork spanner, extremely flat construction, in series galvanised, capacity 1 t, peg Ø 35 mm, measurements 530x380x120 mm
Prismatic blocks
For GA IV | 2 pieces
Run-up ramps 2510 mm
For all surface installation versions | 1 pair
Drive-On ramp for above-ground installation
Extension Kit for drive-on ramp, for above-ground installation
Pads
Support plate | for Mercedes G-Class – front and rear | 1 set / 4 pieces
Second control unit
For SPOA3TS – not suitable for EV | 1 piece
Front and rear adapters for HydroLift 6,2
For lifting various tractors, incl. various receiving means – agricultural receiving means for HydroLift, load capacity 16.4 t
Pads
Support plate, U-support | 1 set / 4 pieces
Axial traverse ATEB S2 TWIN
7.5 – 15 t, 55 mm peg diameter
Extension of the pit crossing SPZ-15
Pit crossing as retrofit kit
Pads
Support plate, centering mushroom | for Fiat 500E, 500 ABARTH | 2-stage | 1 set / 4 pieces
Supporting bridge GSV
Adjustable 900 – 1180 mm, capacity 15 t, with Rollerset
Traverse HydroLift | 16.4 t
King pin support
Extension Kit for ramps
Jacking Beam 2.6 t
Capacity 2600 kg
Jacking Beam 4.0 t
Capacity 4000 kg
Traverse HydroLift
Capacity 12.4 t
Traverse HydroLift | 12.4 t
King pin support
Twin control
(2 lifts, synchronized or individually controllable)
Jacking Beam 2,6 t
Capacity 2600 kg
Pads
Mandrel | for Mercedes Sprinter, VW Crafter – front / for SPO54 | 1 set / 2 pieces
Tool trays
Magnetic | 1 set / 2 pieces
Energy kit for vertical scissor lifts
Compressed air connection under the track, 230 V socket at the control panel | 1 piece
Pads
Prism, mandrel | for Mercedes Sprinter, VW Crafter | 1 set / 6 pieces
Run-up ramps
Additional ramps, 900 mm | 1 set
Supporting bridge SPZ-15
Pads
Mandrel | for Fiat Ducato, Peugeot Boxer, Citroën Jumper – front and rear | 1 set / 4 pieces
Pads
Support plate | for VW MEB platform E-vehicles | 1 set / 4 piece
Seat for turntables | plates and slip plates excluded | 1 set
For RAV4350, RAV4401, RAV4405L, RAV4501L, RAV4651L, RAV4800
Power Kit 230 V
Co mmutateur de position de stationnement
Pad
Support plate, rubber pad, round | Ø 123 mm | 3-stage | 1 piece
Pads
Prism | for Mercedes Sprinter, VW Crafter – rear / for SPO54/55 | 1 set / 2 pieces
Rubber pad
Round | Ø 123 mm | for pad FJ6202 | 1 piece
Washing Bay Kit HDVL
Adjustable drive
Additional adjustable drive to mobilise the fixed lifting unit, incl. extended hanging control pad, reversing device, chain and cover
Automatic ”run-into” protection
Light barrier max.15 m
Automatic ”run-into” protection
Position indicator for craneway
Automatic ”run-into” protection
Mount for automatic ”run-into” protection according to requirements
Automatic axle distance preselection
AAV-Control
Cable suspension
Balancer to disconnect hand-held control panel
Cable suspension
Mount for running rail according to requirements
Roll cover Flexcover
driveable with 5.0t wheel load, galvanized
Temporary cover
Wooden slats to insert in frame, capacity: max. 100 kg/m², per meter
Trolley SmartCart
for DUPLEX load-carrying equipment, incl. 4 swiveling rollers
Aggregate support Universal | for W221, W164, W209, R171
Weight 20 kg, max. load capacity 800 kg