Accessories lifts
Accessories for workshop lifts can seriously make a difference. Our selection of accessories lifts includes kits, rubber pads, covers and much more.
Showing 100–198 of 466 results
Traverse for HydroLift 7,5/8,2
16.4 t
Vehicles lift platforms
Ramp height 60 mm, for extremely low vehicles | 1 set / 2 pieces
Drive-on ramp kit
For above-ground installation
Extension Kit for drive-on ramp, for above-ground installation
Second control unit
For SPOA3TS – not suitable for EV | 1 piece
Traverse for HydroLift S3 7,5/8,2
Max. load bearing capacity 16.4 t, king pin support | only in conjunction with traverse (item no. 119777)
Control unit installation kit
2 m, control unit left | mounting the operating unit in a special position – in drive-up direction “left” from the platform, at a distance of 2 m
Control unit installation kit
2 m, control unit right | mounting the operating unit in a special position – in drive-up direction “right” from the platform, at a distance of 2 m
Tool support
Ergonomic holder for impact wrench
Gearbox-plates GA III
Adjustment angle: ± 40° / ±17°, tensioning belt to secure the load, measurements adjustable to 600 x 400 mm, capacity 1 t, peg Ø 35 mm, measurements 400×300 mm
Gearbox-plates GA IV
Adjustment angle= ± 12°, weight = 23 kg, large rubber supporting surface, tensioning belts to secure the load, comfortable tilting in all directions by fork spanner, extremely flat construction, in series galvanised, capacity 1 t, peg Ø 35 mm, measurements 530x380x120 mm
Power Kit 230 V
Prismatic blocks
For GA IV | 2 pieces
Run-up ramps 2510 mm
For all surface installation versions | 1 pair
Extension Kit for ramps
Jacking beam for SM40-SM65 | 2.6 t
2.6 t
Jacking beam for SM65 4.0 t
4.0 t
Pads
Support plate | for Mercedes G-Class – front and rear | 1 set / 4 pieces
Traverse for HydroLift 6,2
Max. load bearing capacity 12.4 t, king pin support | only in conjunction with traverse (item no. 120204)
Traverse for HydroLift 6,2
12.4 t
Drive-on ramp kit
Additional ramps, 900 mm | 1 set
Front and rear adapters for HydroLift 6,2
For lifting various tractors, incl. various receiving means – agricultural receiving means for HydroLift, load capacity 16.4 t
Pads
Support plate, U-support | 1 set / 4 pieces
Axial traverse ATEB S2 TWIN
7.5 – 15 t, 55 mm peg diameter
Extension of the pit crossing SPZ-15
Pit crossing as retrofit kit
Pads
Support plate, centering mushroom | for Fiat 500E, 500 ABARTH | 2-stage | 1 set / 4 pieces
Supporting bridge GSV
Adjustable 900 – 1180 mm, capacity 15 t, with Rollerset
Twin control
(2 lifts, synchronized or individually controllable)
Jacking Beam 2,6 t
Capacity 2600 kg
Pads
Mandrel | for Mercedes Sprinter, VW Crafter – front / for SPO54 | 1 set / 2 pieces
Tool trays
Magnetic | 1 set / 2 pieces
Energy kit for vertical scissor lifts
Compressed air connection under the track, 230 V socket at the control panel | 1 piece
Pads
Prism, mandrel | for Mercedes Sprinter, VW Crafter | 1 set / 6 pieces
Supporting bridge SPZ-15
Pads
Mandrel | for Fiat Ducato, Peugeot Boxer, Citroën Jumper – front and rear | 1 set / 4 pieces
Pads
Support plate | for VW MEB platform E-vehicles | 1 set / 4 piece
Seat for turntables | plates and slip plates excluded | 1 set
For RAV4350, RAV4401, RAV4405L, RAV4501L, RAV4651L, RAV4800
Adjustable drive
Additional adjustable drive to mobilise the fixed lifting unit, incl. extended hanging control pad, reversing device, chain and cover
Automatic ”run-into” protection
Light barrier max.15 m
Automatic ”run-into” protection
Position indicator for craneway
Automatic ”run-into” protection
Mount for automatic ”run-into” protection according to requirements
Automatic axle distance preselection
AAV-Control
Cable suspension
Balancer to disconnect hand-held control panel
Cable suspension
Mount for running rail according to requirements
Roll cover Flexcover
driveable with 5.0t wheel load, galvanized
Temporary cover
Wooden slats to insert in frame, capacity: max. 100 kg/m², per meter
Trolley SmartCart
for DUPLEX load-carrying equipment, incl. 4 swiveling rollers
Aggregate support Universal | for W221, W164, W209, R171
Weight 20 kg, load capacity 800 kg
LED lighting kit 4-fold, 24 V, 4300 mm
Supporting arm extensions
250 mm | for SPO55 | 1 set / 4 pieces
Universal support Ø 35 mm
Mounting hole Ø 35 mm, suitable for holding various tools, such as the transmission plate GA passenger car | fitted with a bushing
Pads
Prism | for Mercedes Sprinter, VW Crafter – rear / for SPO54/55 | 1 set / 2 pieces
Rubber pad
Round | Ø 123 mm | for pad FJ6202 | 1 piece
Stand for the control cabine | 600 mm
1 piece
Cassette extended (primary coated)
Incl. FLEXCOVER, per meter
Cassette galvanized
Instead of primary coat, per meter
Frame extended (primary copated)
Incl. FLEXCOVER, per meter
Frame galvanized
Instead of primary coat, per meter
Frame with overhang
Frame incl. FLEXCOVER, each piece
Frame with overhang
Frame, galvanised execution, incl. FLEXCOVER, each piece
Pump sump
for lift cassette
Washing Bay Kit HDVL
Wheel alignment kit Standard
N-type, incl. 2 balance plates | for 4-post lift SM40-47 | Grey (RAL 7040)
Floor stand
800 mm wide (for T/L-4 platform)
Floor stand
1000 mm wide (for T/L-5 platform)
Wheel alignment kit Standard
Height 75 mm, consisting of filling plates and 4 shifting plates, without turntables | for 4-post lift SM55LT-51 | Grey (RAL 7040) | ramp extension EXRMP-SM40N recommended
Wheel alignment kit Standard | for SM65-51
N-type, height 50 mm, consisting of filling plates and 4 shifting plates, without turntables | for 4-post lift SM65-51 | Grey (RAL 7040) | ramp extension EXRMP-SM40N recommended
Wheel alignment kit Standard | for SM65-55
N-type, height 50 mm, consisting of filling plates and 4 sliding plates, without turntables | for 4-post lift SM65-55 | Grey (RAL 7040) | EXRMP-SM40N ramp extension recommended
Wheel alignment kit Standard
N-type, height 50 mm, consisting of filling plates and 2 shifting plates, without turntables | for 4-post lift SM40LT-47 | Grey (RAL 7040)
Jacking beam check positioning kit
Pads
Support plate, rubber support, round | Ø 80 mm | 1 set / 4 pieces
Vehicle fuses
For turntable, Ø 120 mm | 1 set / 2 pieces
Energy kit for S42/S50
230 volt socket at the control panel
Extension for MRG55
100 mm (3000/4000/5500 kg) / 150 mm (7000/8500/10000 kg)
SmartCart Agrar
for tractor adapter set HydroLift
Wheel fork reduction for tires Ø 900 – 800 mm
1 piece
Wheel free cross-beam for MRG55
15 t
Support plate X
20 t, 55 mm peg diameter
Traverse ATEB S2
7.5 – 15 t, 55 mm peg diameter
Drive-through ramps 2510 mm
Additional ramps to drive-through the lift | 1 set / 2 pieces
Drive-through ramps 3300 mm
Additional ramps to drive-through the lift | 1 set / 2 pieces
Floor leveling for HDVL 25/35-130/145-I
For vertical scissor lifts with 13/14.5 m platform length
Floor leveling for HDVL 25/35-130/145-I | galvanized
For vertical scissor lifts with 13/14.5 m platform length
Synchronization control Twin
2 lifts actionable individually or synchronised
Floor leveling for HDVL 25/35-100-I | galvanized
For vertical scissor lifts with 10 m platform length
Hydraulic lifting drawbar for MRG55
Capacity 3000/4000/5500 kg | replaces the standard jack
Accessory kit above ground S42-S50, crossing ramps 1,60 m
2 drive-over ramps for lifting platform with wheel-free jack (LT version)
Accessory kit above ground S42-S50, crossing ramps 1,90 m
Drive-over ramps long for lifting platform with wheel-free jack (LT version)
Accessory kit above ground S42-S50, ramps 1,60 m
Overfloor kit for lifting platform with wheel-free jack (LT version) | Ramps and cover plates for hoses
Accessory kit above ground S42-S50, ramps 1,90 m
Above ground kit long ramps for lifting platform with wheel-free jack (LT version) | Ramps and cover plates for hoses
Floor leveling for HDVL 25/35-100-I
For vertical scissor lifts with 10 m platform length
Floor leveling for HDVL 25/35-110-I
For vertical scissor lifts with 11 m platform length
Floor leveling for HDVL 25/35-110-I | galvanized
For vertical scissor lifts with 11 m platform length
Floor leveling for HDVL 25/35-120-I
For vertical scissor lifts with 12 m platform length
Floor leveling for HDVL 25/35-120-I | galvanized
For vertical scissor lifts with 12 m platform length
Floor leveling for HDVL 25/35-60-I
For vertical scissor lifts with 6 m platform length
Floor leveling for HDVL 25/35-60-I | galvanized
For vertical scissor lifts with 6 m platform length
Floor leveling for HDVL 25/35-80-I
For vertical scissor lifts with 8 m platform length
Floor leveling for HDVL 25/35-80-I | galvanized
For vertical scissor lifts with 8 m platform length